# Girodisc 345x30 Front Brake Discs for Hyundai Veloster N (2019+)

> Pair of Girodisc front disks, 345 × 30 mm, part no.: A1-217. High-performance floating brake discs on an aluminum hub for the Hyundai Veloster N (2019+).

- URL: https://www.gt2i.ch/en/brake-disk-for-bell/224534-girodisc-345x30-front-brake-discs-for-hyundai-veloster-n-2019-3666618858593.html
- Reference: GIRO-A1-217
- Price: CHF 1,206.46
- Brand: GIRODISC
- Availability: out of stock

## Description

The Girodisc A1-217 front brake discs, measuring 345 × 30 mm, improve thermal management during repeated braking on the Hyundai Veloster N (2019+). Their cast-iron rotors and aluminum hubs form a floating assembly designed to handle thermal stresses and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.
These rotors are intended for the front axle of compatible vehicles in the configuration shown below. They retain the compatible calipers; any required spacers and brake pad specifications must be followed.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting limits stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.
The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. Washer springs minimize cold-mounting noise while allowing the necessary compression for the floating mount.
New brake pads must be installed with new discs or rotors. Their shape and compound must be compatible with the mounting, casting, and intended use; adhere to the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc A1-217 discs for compatible vehicles
Brand: Girodisc
PartNumber: A1-217
Position: front
Sizes (diameter × thickness): 345 × 30 mm
Vehicles and models: Hyundai Veloster N (2019+)
Braking surface material: high-resistance cast steel
Packaging: Pair of complete rotors, one left and one right with disc bells.
Housing: 6061-T6 aluminum
Construction: two-piece floating mounting design
Catalog part number: D1-217. Verify compatibility with the caliper generation before replacement.
Internal ventilation: directional curved fins
Minimum thickness: 28 mm
Overall height: 52.6 mm
Original rotor diameter: 345 mm
Manufacturing of main components: United States
Vehicles compatible with Girodisc part number A1-217
Hyundai Veloster N (2019+)
Hyundai Veloster N (2019+): 2019–2020 model years with performance pack.
Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.
Mounting requirements for Girodisc A1-217
Hyundai Veloster N (2019+): 2019–2020 model years with performance pack.
Brake Pads and Brake System for Compatible Vehicles
Choose brake pads whose shape is compatible with the calipers, track, and/or the A1-217 rotor, and whose compound is suitable for sport driving or track use. The Endless, pagid Racing, or Ferodo Racing ranges may be considered after verifying the appropriate part number.
For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements a mounting compatible with the original hydraulic system.
Maintenance of the Girodisc mounting on compatible vehicles
Replacing the pads alone helps keep the controlled rotors in good condition. Reusing a rotor for up to three pad replacements is subject to inspection of its condition, its mounting components, and the mounting instructions; this number does not constitute a guaranteed service life. Use a new mounting component each time you replace the pads.
FAQ — Girodisc A1-217 for Compatible Vehicles
What are the sizes of the A1-217 discs for my vehicle? The part number shown measures 345 × 30 mm and is mounted on the front axle. The diameter alone is not sufficient: also check the brake system type and mounting requirements.
Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.
Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the A1-217 track and/or rotor and with the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc A1-217 Bowl Brake Discs
345 × 30 mm size for front braking on compatible vehicles.
6061-T6 aluminum rotor and floating mount to manage thermal stresses.
Internal ventilation via curved fins to dissipate heat.
Replaceable pads to maintain a two-piece mounting.
Left/right pair identified for mounting.
Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast-iron disc.

## Features

- Product type: Brake disc on a Bol
- Diameter in mm: 345
- Position: Avant
- Thickness: 30