# One-piece brake rotors for the rear brakes of the Mercedes CLS63 (W218) (2012–2018) – E63 (W212) (2012–2016) with CCB

> Pair of Girodisc rear brake pads, 358 × 32 mm, part no.: D2-240. Replacement cast iron brake pads for Girodisc floating rotors, compatible with Mercedes CLS63 (W218) with CCB (2012–2018); Mercedes E63 (W212) with CCB (2012–2016); Mercedes SLS with CCB (2010–2015). Rotors not included.

- URL: https://www.gt2i.ch/en/brake-rotor/224172-one-piece-brake-rotors-for-the-rear-brakes-of-the-mercedes-cls63-w218-20122018-e63-w212-20122016-with-ccb-3666618854977.html
- Reference: GIRO-D2-240
- Price: CHF 1,087.00
- Brand: GIRODISC
- Availability: out of stock

## Description

The Girodisc D2-240 rear alternative brake pads (358 × 32 mm) allow you to replace the braking surfaces on the Mercedes CLS63 (W218) with carbon-ceramic rotors (2012–2018), the Mercedes E63 (W212) with carbon-ceramic rotors (2012–2016), and Mercedes SLS models with carbon-ceramic rotors (2010–2015), while retaining the compatible brake caliper housings after inspection. These cast-iron rotors maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without caliper housings.
The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the rotor and the caliper housing and helps the rotor center itself between the brake pads to maintain consistent contact when hot.
New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting configuration, cast material, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc D2-240 rotors for compatible vehicles
Brand: Girodisc
PartNumber: D2-240
Position: rear
Sizes (diameter × thickness): 358 × 32 mm
Vehicles and models: Mercedes CLS63 (W218) with carbon-ceramic rotors (2012–2018); Mercedes E63 (W212) with carbon-ceramic rotors (2012–2016); Mercedes SLS with carbon-ceramic rotors (2010–2015)
Braking surface: cast iron
Packaging: pair of brake pads, one left and one right; rotors not included.
Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with original equipment rotors.
Mounting hardware: new parts supplied with the kit; replace the entire track-to-cup mounting assembly during reassembly.
Part number for corresponding complete rotors: A2-240.
Internal ventilation: directional curved fins
Manufacturing of main components: United States
Vehicles compatible with Girodisc part number D2-240
Mercedes CLS63 (W218) with carbon-ceramic rotors (2012–2018)
Compatibility and mounting requirements:
For vehicles with factory-installed carbon-ceramic brakes.
Mercedes E63 (W212) with carbon-ceramic rotors (2012–2016)
Compatibility and mounting requirements:
For vehicles with factory-installed carbon-ceramic brakes.
Mercedes SLS with carbon-ceramic rotors (2010–2015)
Compatibility and mounting requirements:
For vehicles with factory-installed carbon-ceramic brakes.
Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.
Brake Pads and Brake System for Compatible Vehicles
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed to withstand high braking loads. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc D2-240 for compatible vehicles
What are the sizes of the D2-240 pads for my vehicle? The model shown measures 358 × 32 mm and is mounted on the rear axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.
Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake drums are not included.
Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the D2-240 track and/or rotor and the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc D2-240 Alternative Tracks
358 × 32 mm size for rear braking on compatible vehicles.
Internal ventilation via curved fins to dissipate heat.
Replaceable alternative tracks to maintain a two-piece mounting.
Left/right pair identified for mounting.
Compatible aluminum brake rotors are retained to maintain the benefits of the two-piece mounting on unsprung and rotating masses.

## Features

- Product type: Alternative Track
- Diameter in mm: 358
- Position: Rear
- Thickness: 32
