# One-piece brake rotors for the front or rear, 330x28, for Ferrari 360 (1999–2005) – F430 without CCB

> Pair of Girodisc front or rear brake pads, 330 × 28 mm, part no.: D1-001. Replacement cast-iron pads for Girodisc floating rotors, compatible with the Ferrari 360 (1999–2005) and the Ferrari F430 without CCB (2004–2009). Rotors not included.

- URL: https://www.gt2i.ch/en/brake-rotor/224385-one-piece-brake-rotors-for-the-front-or-rear-330x28-for-ferrari-360-19992005-f430-without-ccb-3666618857107.html
- Reference: GIRO-D1-001
- Price: CHF 967.00
- Brand: GIRODISC
- Availability: out of stock

## Description

Girodisc D1-001 front or rear alternative brake pads (330 × 28 mm) allow you to replace the braking surfaces on Ferrari 360s (1999–2005) and Ferrari F430s without carbon-ceramic rotors (2004–2009) while retaining the compatible brake rotors after inspection. These cast-iron pads maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without brake rotors.
This part can be installed on the front or rear, depending on the application. It is sold in pairs for a single axle; it is not a set of four components.
The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the track and the caliper housing and helps the track center itself between the brake pads to maintain consistent contact when hot.
New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting configuration, cast material, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc D1-001 tracks for compatible vehicles
Brand: Girodisc
PartNumber: D1-001
Position: front or rear, depending on the application
Sizes (diameter × thickness): 330 × 28 mm
Vehicles and models: Ferrari 360 (1999–2005); Ferrari F430 without carbon-ceramic brake disks (2004–2009)
Braking surface material: cast iron
Packaging: pair of brake pads, one left and one right; rotors not included.
Compatible calipers: calipers from the corresponding Girodisc kit; check by part number; not universally compatible with original equipment calipers.
Mounting hardware: Sport mounting kit included; replace the entire track-to-caliper mounting assembly during reassembly.
Part number for corresponding complete rotors: A1-001.
Internal ventilation: directional curved fins
Number of internal fins: 48
Minimum thickness: 26 mm
Original rotor diameter: 330 mm
Manufacturing of main components: United States
Vehicles compatible with Girodisc part number D1-001
Ferrari 360 (1999–2005)
Compatibility and mounting requirements:
— front
— rear
Ferrari F430 without carbon-ceramic brake rotors (2004–2009)
Compatibility and mounting requirements:
— front
Excludes carbon-ceramic braking systems.
Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.
Brake pads and brake systems for compatible vehicles
For sports or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the shape of the brake pads remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement brake pads for Girodisc rotors on compatible vehicles
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc D1-001 for compatible vehicles
What are the sizes of the D1-001 pads for my vehicle? The part shown measures 330 × 28 mm and is mounted on the front axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.
Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake shoes are not included.
Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the D1-001 track and/or rotor and the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc D1-001 Alternative Tracks
330 × 28 mm size for front braking on compatible vehicles.
Internal ventilation via curved fins to dissipate heat.
Replaceable alternative tracks to maintain a two-part mounting.
Left/right pair identified for mounting.
Compatible aluminum rotors are retained to preserve the benefits of the two-piece mounting on unsprung and rotating masses.

## Features

- Product type: Alternative Track
- Diameter in mm: 330
- Position: Avant/Arrière
- Thickness: 28
