GT2i FIA Race-02M -V2 Fiber seat

Our philosophy :

We wanted to adapt our seats to the evolution of the seating position over time. In the past, with cars not equipped with power steering and longer rallyes. Nowadays, with shorter stages, faster more direct input cars. When strength and stamina was needed, today's key words are speed, accuracy, comfort and adaptability. It was crucial to take into account every of these evolutions for the making of our bucket seats range.

A fitting for various tilting options !

PLEASE NOTE: Valid until 31/12/2030 for declination .30 !

Finally, the shell has been improved to make it easier to install the seat in your vehicle. 

Features :

Injecte resin shell seat

M size seat

Certification FIA 8855-1999

MANUFACTURER: FLB

MODEL: RACE-02M

HOM. NO: CS.462.20

FIA STANDARD: 8855-1999

Side (center distance 290mm) mounting frames

Weight : 8.1kg

Lumbar, base adjustments and thigh brackets by padding overlay.

Magnet to retain the harness.

Honeycomb mesh fabric.

Sold with 4 BTR screws + washers for the mounting.

Less detail

The GT2i Race 6-point harness uses 100% polyester straps and can withstand forces of 3800 Newton.
The steel adjusters incorporate a spring to optimize tightening.
The yellow tabs allow you to loosen the straps quickly to untie yourself at the finish line.
This sedan harness also has a Velcro® strap for attaching a radio cable or water dropper.

The C40 steel aviation buckle meets the specifications and precise tolerances of the FIA standard. It receives C60 carbon steel fasteners.
Its central buckle has been redesigned to facilitate the locking and unlocking of the harness while reinforcing the mechanism to increase safety and at the same time prevent the entry of impurities inside the system.

Valid until 12/31/2029 for .29 versions
Valid until 12/31/2030 for .30 versions

Features :

Shoulder straps: 2"/3" HANS® specific
Abdominal straps: 3".
Aviation buckle on 6th point.

Made in Europe.
Delivered without eyelets

Certification FIA 8853-2016

MANUFACTURER: MCF S.R.L.

MODEL: 50100514

HOM. NO: SH.092.22-T-6

FIA STANDARD: 8853-2016

Less detail

Our philosophy :

We wanted to adapt our seats to the evolution of the seating position over time. In the past, with cars not equipped with power steering and longer rallyes. Nowadays, with shorter stages, faster more direct input cars. When strength and stamina was needed, today's key words are speed, accuracy, comfort and adaptability. It was crucial to take into account every of these evolutions for the making of our bucket seats range.

A fitting for various tilting options !

PLEASE NOTE: Valid until 31/12/2030 for declination .30 !

Finally, the shell has been improved to make it easier to install the seat in your vehicle. 

Features :

Injecte resin shell seat

M size seat

Certification FIA 8855-1999

MANUFACTURER: FLB

MODEL: RACE-02M

HOM. NO: CS.462.20

FIA STANDARD: 8855-1999

Side (center distance 290mm) mounting frames

Weight : 8.1kg

Lumbar, base adjustments and thigh brackets by padding overlay.

Magnet to retain the harness.

Honeycomb mesh fabric.

Sold with 4 BTR screws + washers for the mounting.

Less detail

Our philosophy :

We wanted to adapt our seats to the evolution of the seating position over time. In the past, with cars not equipped with power steering and longer rallyes. Nowadays, with shorter stages, faster more direct input cars. When strength and stamina was needed, today's key words are speed, accuracy, comfort and adaptability. It was crucial to take into account every of these evolutions for the making of our bucket seats range.

A fitting for various tilting options !

PLEASE NOTE: Valid until 31/12/2030 for declination .30 !

Finally, the shell has been improved to make it easier to install the seat in your vehicle. 

Features :

Injecte resin shell seat

M size seat

Certification FIA 8855-1999

MANUFACTURER: FLB

MODEL: RACE-02M

HOM. NO: CS.462.20

FIA STANDARD: 8855-1999

Side (center distance 290mm) mounting frames

Weight : 8.1kg

Lumbar, base adjustments and thigh brackets by padding overlay.

Magnet to retain the harness.

Honeycomb mesh fabric.

Sold with 4 BTR screws + washers for the mounting.

Less detail