The GT2i Race 6-point harness uses 100% polyester straps and can withstand forces of 3800 Newton.
The steel adjusters incorporate a spring to optimize tightening.
The yellow tabs allow you to loosen the straps quickly to untie yourself at the finish line.
This sedan harness also has a Velcro® strap for attaching a radio cable or water dropper.
The C40 steel aviation buckle meets the specifications and precise tolerances of the FIA standard. It receives C60 carbon steel fasteners.
Its central buckle has been redesigned to facilitate the locking and unlocking of the harness while reinforcing the mechanism to increase safety and at the same time prevent the entry of impurities inside the system.
PLEASE NOTE: Valid until December 31, 2031 for the .31 version!
Features :
Shoulder straps: 2"/3" HANS® specific
Abdominal straps: 3".
Aviation buckle on 6th point.
Made in Europe.
Delivered without eyelets
Certification FIA 8853-2016
MANUFACTURER: MCF S.R.L.
MODEL: 50100514
HOM. NO: SH.092.22-T-6
FIA STANDARD: 8853-2016
Our philosophy :
We wanted to adapt our seats to the evolution of the seating position over time. In the past, with cars not equipped with power steering and longer rallyes. Nowadays, with shorter stages, faster more direct input cars. When strength and stamina was needed, today's key words are speed, accuracy, comfort and adaptability. It was crucial to take into account every of these evolutions for the making of our bucket seats range.
A fitting for various tilting options !
PLEASE NOTE: Valid until December 31, 2031 for the .31 version!
Tested by various body types, the GT2i Race-02 M V2 base was designed for a slightly more tilted driving position for increased comfort and safety in case of a potential crash. The driver is held in place, both at the thighs and shoulders while keeping a great freedom of movements for a quick steering input.
Their anatomic design allows for a wide variety of adjustments up to a more upright position for older vehicles thanks to the wide adjustments possibilities offered by our mounting frames (GT-FIX001).
Back padding is designed to match the drivers spine and offer perfect comfort. Padding can be either added in the lower back and bottom cushions to refine the driving position. Mesh cloth offers breathability for the backrest. 3 magnets are integrated to retain the harness straps on the sides and base of the seat.
Finally, the shell has been improved to make it easier to install the seat in your vehicle.
Features :
Injecte resin shell seat
M size seat
Certification FIA 8855-1999
MANUFACTURER: FLB
MODEL: RACE-02M
HOM. NO: CS.462.20
FIA STANDARD: 8855-1999
Side (center distance 290mm) mounting frames
Weight : 8.1kg
Lumbar, base adjustments and thigh brackets by padding overlay.
Magnet to retain the harness.
Honeycomb mesh fabric.
Sold with 4 BTR screws + washers for the mounting.
This Race M bucket seat + GT2i Race harness package is designed for a sedan intended for competition or track days, combining a size M bucket seat with an FIA-approved 6-point harness. The package is designed to improve driver support, stability under cornering, and cockpit seating position, while meeting the approval requirements specified for each component. The GT2i Race 6-point sedan harness is FIA 8853-2016 approved. Its 6-point configuration provides effective force distribution and enhanced support for the pelvis and torso, which is particularly useful during hard braking and rapid direction changes. The shoulder straps have a width of 2"/3" (depending on configuration), with steel adjusters and a pull-up tightening system, designed for precise and repeatable adjustment. The GT2i FIA Race-02M -V2 Fibre 2026 seat, size M, is FIA 8855-1999 approved (homologation number: CS,462,20). It is a side-mounted seat with a fiberglass shell and fabric upholstery. The recline is not adjustable, which enhances the overall rigidity of the seat and ensures a consistent driving position. Its weight is listed as 8.1 kg, helping to minimize the impact on the vehicle’s curb weight while maintaining a competition-oriented design. Vehicle compatibility and mounting hardware: Not specified.
