Girodisc 350x28 Rear Brake Discs for Porsche Boxster (981) Spyder (2015–2016) – 718 (982) Cayman – Boxster GTS 4.0 (2016+) witho

GIRODISC
Reference: GIRO-A2-049B
Supplier Ref.: A2-049B

Price: CHF 1,631.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 1631 loyalty points (that is CHF 85.00 in vouchers)

The Girodisc A2-049B rear brake discs, measuring 350 × 28 mm, enhance braking endurance during sustained use on Porsche Boxster (981) Spyder models without carbon-ceramic rotors (2015–2016), Porsche 718 (982) Cayman and Boxster GTS 4.0 (2016+). Their cast-iron pads and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate pad replacement due to wear. Sold in pairs, with one left and one right disc.

These rotors are intended for the rear axle of compatible vehicles in the configuration listed below. They retain the compatible caliper mounting; any required spacers and brake pad specifications must be followed.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.

The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.

New pads must be installed with new discs or tracks. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; comply with the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc A2-049B rotors for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A2-049B
  • Position: rear
  • Sizes (diameter × thickness): 350 × 28 mm
  • Vehicles and models: Porsche Boxster (981) Spyder without carbon-fiber brake disks (2015–2016); Porsche 718 (982) Cayman and Boxster GTS 4.0 (2016–)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right with disc bells.
  • Housing: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Replacement part number for these rotors: D2-049. Verify compatibility with the caliper generation before replacement.
  • Internal ventilation: directional curved fins
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-049B

Porsche Boxster (981) Spyder without carbon-ceramic rotors (2015–2016)

Compatibility and mounting requirements:

Without PCCB.

Use the rear brake pads from the Porsche 911 (991) Carrera S, 4S, or GTS to cover the braking surface.

Porsche 718 (982) Cayman and Boxster GTS 4.0 (2016+)

Compatibility and mounting requirements:

350 mm rear mounting; use 991 S brake pads to cover the entire brake surface.

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake Pads and Brake Systems for Compatible Vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A2-049B for compatible vehicles

What are the sizes of the A2-049B discs for my vehicle? The part number shown measures 350 × 28 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your use. Use the rear brake pads from a Porsche 911 (991) Carrera S, 4S, or GTS to cover the braking surface.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the rotors, and an instruction manual for installing new tracks on existing rotors. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A2-049B Two-Piece Brake Rotors

  • 350 × 28 mm size for rear braking on compatible vehicles.
  • 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable tracks to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast-iron disc.

  • Diameter in mm
    350
  • Position
    Rear
  • Thickness
    28

16 other products in the same category: