Girodisc 335x32 Rear Brake Discs - Ford GT (2005-2006)

GIRODISC
Reference: GIRO-A2-043
Supplier Ref.: A2-043

Price: CHF 1,812.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 1812 loyalty points (that is CHF 100.00 in vouchers)

The Girodisc A2-043 rear brake discs, measuring 335 × 32 mm, improve thermal management during repeated braking on Ford GTs (2005–2006). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.

These rotors are intended for the rear axle of compatible vehicles in the configuration shown below. They retain the compatible caliper mounting; any required spacers and brake pad specifications must be followed.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.

The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.

New brake pads must be installed with new discs or rotors. Their shape and compound must be compatible with the mounting, casting, and intended use; adhere to the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc A2-043 discs for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A2-043
  • Position: rear
  • Sizes (diameter × thickness): 335 × 32 mm
  • Vehicles and models: Ford GT (2005–2006)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right with disc bells.
  • Hub: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Replacement part number for these rotors: D2-043. Verify compatibility with the caliper generation before replacement.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 30 mm
  • Overall height: 53 mm
  • Original rotor diameter: 335 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-043

Ford GT (2005–2006)

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake pads and braking systems for compatible vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed to withstand high braking loads. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement Brake Pads for Ford GT (2005–2006) Girodisc Rotors

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A2-043 for Compatible Vehicles

What are the sizes of the A2-043 discs for my vehicle? The model shown measures 335 × 32 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs are shipped with their hubs.

Do I need to perform a pad change on my vehicle?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the A2-043 track and/or rotor and with the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the rotors, and an instruction manual for installing new tracks on existing rotors. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A2-043 Two-Piece Brake Discs

  • 335 × 32 mm size for rear braking on compatible vehicles.
  • 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable tracks to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.

  • Diameter in mm
    335
  • Position
    Rear
  • Thickness
    32

16 other products in the same category: