Girodisc 300x22 Rear Brake Discs - Mitsubishi Lancer Evo 6-9 (1998-2008)

GIRODISC
Reference: GIRO-A2-008
Supplier Ref.: A2-008

Price: CHF 1,148.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 1147 loyalty points (that is CHF 60.00 in vouchers)

The Girodisc A2-008 rear brake discs, measuring 300 × 22 mm, optimize consistent braking performance during spirited driving in the Mitsubishi Lancer Evo 6-9 (1998-2008). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stress and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.

These rear discs are intended for the rear axle of compatible vehicles in the configuration shown below. They retain the calipers from the compatible mounting; any required spacers and brake pad specifications must be followed.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.

The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-trimmed to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.

New pads must be installed with new discs or tracks. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; comply with the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc A2-008 rotors for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A2-008
  • Position: rear
  • Sizes (diameter × thickness): 300 × 22 mm
  • Vehicles and models: Mitsubishi Lancer Evo 6-9 (1998-2008)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right with disc bells.
  • Housing: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Alternative track number for these rotors: D2-008. Verify compatibility with the caliper generation before replacement.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 20 mm
  • Overall height: 58 mm
  • Original rotor diameter: 300 mm
  • Weight / weight reduction: Comparison stated in the manufacturer’s data sheet: approximately 5.44 kg per disc versus 6.58 kg for the original, for a weight savings of 1.13 kg per disc (2.27 kg per pair).
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-008

Mitsubishi Lancer Evo 6-9 (1998-2008)

Compatibility and mounting requirements:

The metal brackets on the original brake pads and certain aftermarket pads require adjustment to clear the rotor mounting while retaining the parking brake. It is essential to follow the instructions and use pre-prepared pads when available.

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Check these requirements before ordering.


Brake Pads and Brake Systems for Compatible Vehicles

For sports or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the shape of the brake pads remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. Aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A2-008 for compatible vehicles

What are the sizes of the A2-008 discs for my vehicle? The model shown measures 300 × 22 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new brake discs or new braking surfaces. Use a compound suitable for cast iron and your specific use. The metal brackets on the original brake pads and on some aftermarket pads require adjustment to clear the brake disc mounting while maintaining the parking brake. It is essential to follow the instructions and use pre-prepared pads when available.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A2-008 Two-Piece Brake Discs

  • 300 × 22 mm size for rear braking on compatible vehicles.
  • 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable tracks to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.

  • Diameter in mm
    300
  • Position
    Rear
  • Thickness
    22

16 other products in the same category: