Girodisc 316x20 Rear Brake Discs - Subaru Impreza WRX STi (2004-2007)

GIRODISC
Reference: GIRO-A2-007
Supplier Ref.: A2-007

Price: CHF 1,148.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 1147 loyalty points (that is CHF 60.00 in vouchers)

The Girodisc A2-007 rear brake discs, measuring 316 × 20 mm, improve heat management during repeated braking on the Subaru Impreza WRX STi (2004–2007). Their cast iron rotors and aluminum hubs form a floating assembly designed to handle thermal stresses and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.

These rear discs are intended for the rear axle of compatible vehicles in the configuration shown below. They retain the compatible calipers; any required spacers and brake pad specifications must be followed.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.

The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-trimmed to resist corrosion. They are secured by Class 12.9 bolts and hardened washers. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.

New pads must be installed with new discs or tracks. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; comply with the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc A2-007 rotors for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A2-007
  • Position: rear
  • Sizes (diameter × thickness): 316 × 20 mm
  • Vehicles and models: Subaru Impreza WRX STi (2004–2007)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right with disc bells.
  • Housing: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Replacement part number for these rotors: D2-007. Verify compatibility with the caliper generation before replacement.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 18 mm
  • Overall height: 68 mm
  • Original rotor diameter: 316 mm
  • Weight / weight reduction: Comparison stated in the manufacturer’s data sheet: approximately 4.99 kg per disc versus 8.16 kg for the original, representing a weight savings of 3.18 kg per disc (6.35 kg per pair).
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-007

Subaru Impreza WRX STi (2004–2007)

Compatibility and mounting requirements:

Rear brake pad brackets must be modified.

The metal brackets on the original equipment and certain aftermarket pads require adjustment to clear the brake disc mounting while retaining the parking brake. It is essential to follow the instructions and use pre-prepared pads when available.

Each application is specific to its brake system configuration, calipers, and any requirements for brake pads or spacers. Verify these conditions before ordering.


Brake Pads and Brake Systems for Compatible Vehicles

For sports or track use, we recommend Endless, pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the shape of the brake pads remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A2-007 for compatible vehicles

What are the sizes of the A2-007 discs for my vehicle? The part number shown measures 316 × 20 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new brake discs or new braking surfaces. Use a compound suitable for cast iron and your intended use. The metal brackets on the original brake pads and on some aftermarket pads require adjustment to clear the brake disc mounting while maintaining the parking brake. It is essential to follow the instructions and use pre-prepared pads when available.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A2-007 Two-Piece Brake Discs

  • 316 × 20 mm size for rear braking on compatible vehicles.
  • 6061-T6 aluminum bowl and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable brake pads to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.

  • Diameter in mm
    316
  • Position
    Rear
  • Thickness
    20

16 other products in the same category: