Girodisc 390x36 Front Brake Discs - Audi RS6 (C6) (2008-2010)

GIRODISC
Reference: GIRO-A1-196
Supplier Ref.: A1-196

Price: CHF 1,631.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 1631 loyalty points (that is CHF 85.00 in vouchers)

The Girodisc A1-196 front brake discs, measuring 390 × 36 mm, improve thermal management during repeated braking on the Audi RS6 (C6) (2008–2010). Their cast-iron rotors and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate rotor replacement due to wear. Sold as a pair, including one left-side and one right-side rotor.

These rotors are intended for the front axle of compatible vehicles in the configuration specified below. They retain the calipers from the compatible mounting; any required spacers and brake pad specifications must be followed.

The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the pad and the housing and helps the pad center itself between the brake pads, maintaining consistent contact even when hot.

The hub is made of 6061-T6 aluminum.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting, casting, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc A1-196 discs for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A1-196
  • Position: front
  • Sizes (diameter × thickness): 390 × 36 mm
  • Vehicles and models: Audi RS6 (C6) (2008–2010)
  • Braking surface material: cast iron
  • Packaging: Pair of complete rotors, one left and one right with disc bells.
  • Housing: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Alternative track number for these rotors: D1-196. Verify compatibility with the front disk generation before replacement.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 34 mm
  • Overall height: 59.7 mm
  • Original rotor diameter: 390 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A1-196

Audi RS6 (C6) (2008–2010)

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.


Brake pads and braking systems for compatible vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed to withstand high braking loads. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement Brake Pads for Audi RS6 (C6) (2008–2010) Girodisc Rotors

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mounting components, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A1-196 for Compatible Vehicles

What are the sizes of the A1-196 discs for my vehicle? The model shown measures 390 × 36 mm and is mounted on the front axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs are shipped with their hubs.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new rotors or new brake pads. Their shape and compound must be compatible with the A1-196 rotor and/or braking surfaces and the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed in the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc A1-196 Two-Piece Brake Discs

  • 390 × 36 mm size for front braking on compatible vehicles.
  • 6061-T6 aluminum rotor and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable tracks to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum rotors help reduce unsprung and rotating mass compared to a comparable one-piece cast iron disc.

  • Diameter in mm
    390
  • Position
    Front
  • Thickness
    36

16 other products in the same category: