One-piece Girodisc 305x11 rear brake rotors - Honda Civic Type R (FK8, FL5)
Girodisc D2-166 rear alternative tracks (305 × 11 mm) allow you to replace the braking surfaces on Honda Civic Type R (FK8, FL5) models while retaining the compatible brake calipers after inspection. These cast iron rotors maintain the floating assembly’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without calipers.
The cast iron track and floating assembly allow the disc to accommodate differences in thermal expansion between its two halves and to center itself between the brake pads. This construction also makes it easier to replace the tracks when they are worn.
New brake pads must be installed with new rotors or new tracks. Their shape and compound must match the mounting, the cast iron, and the intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.
Specifications for Girodisc D2-166 friction pads for compatible vehicles
- Brand: Girodisc
- PartNumber: D2-166
- Position: rear
- Sizes (diameter × thickness): 305 × 11 mm
- Vehicles and models: Honda Civic Type R (FK8, FL5)
- Braking surface: cast iron
- Packaging: pair of brake pads, one left and one right; rotors not included.
- Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with OEM rotors.
- Mounting hardware: New parts supplied with the kit; replace the entire rotor-to-hub mounting assembly during reinstallation.
- Part number for corresponding complete rotors: A2-166.
- Original rotor diameter: 305 mm
- Manufacturing of main components: United States
Vehicles compatible with Girodisc part number D2-166
Honda Civic Type R (FK8, FL5)
Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.
Brake pads and braking systems for compatible vehicles
For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.
For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.
Replacement Brake Pads for Honda Civic Type R (FK8, FL5) Girodisc Rotors
When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.
FAQ — Girodisc D2-166 for Compatible Vehicles
What are the sizes of the D2-166 pads for my vehicle? The part number shown measures 305 × 11 mm and is mounted on the rear axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.
Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake shoes are not included.
Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the D2-166 track and/or rotor and the calipers. Then break in the rotors and pads according to the prescribed procedures.
How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.
How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.
PDF Documents for Mounting and Break-in
We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.
Key Features of Girodisc D2-166 Alternative Tracks
- 305 × 11 mm size for rear braking on compatible vehicles.
- Replaceable tracks to maintain a two-piece mounting.
- Left/right pair identified for mounting.
- Compatible aluminum rotors are retained to maintain the benefits of the two-piece mounting on unsprung and rotating masses.
-
Diameter in mm305
-
PositionRear
-
Thickness11