One-piece brake rotors 316x20 for Subaru BRZ - Impreza WRX STI (2008–2017) - WRX with Brembo brake calipers (2020)

GIRODISC
Reference: GIRO-D2-095
Supplier Ref.: D2-095

Price: CHF 761.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 761 loyalty points (that is CHF 25.00 in vouchers)

The Girodisc D2-095 rear alternative brake pads (316 × 20 mm) allow you to replace the braking surfaces on the Subaru BRZ, Subaru Impreza WRX STI (2008–2017), and Subaru WRX with Brembo calipers (2020) while retaining the compatible rotors after inspection. These cast iron rotors maintain the floating mounting configuration and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without hubs.

The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting reduces stress caused by thermal expansion differences between the rotor and the caliper housing and helps the rotor center itself between the brake pads, maintaining consistent contact when hot.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must be compatible with the mounting, the cast iron, and the intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc D2-095 tracks for compatible vehicles

  • Brand: Girodisc
  • PartNumber: D2-095
  • Position: rear
  • Sizes (diameter × thickness): 316 × 20 mm
  • Vehicles and models: Subaru BRZ; Subaru Impreza WRX STI (2008–2017); Subaru WRX with Brembo calipers (2020)
  • Braking surface: cast iron
  • Packaging: pair of rotors, one left and one right; hubs not included.
  • Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with OEM rotors.
  • Mounting hardware: Sport mounting kit included; replace the entire track/rotor mounting assembly during reinstallation.
  • Part number for corresponding complete rotors: A2-095.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 18 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number D2-095

Subaru BRZ

Compatibility and mounting requirements:

For Brembo calipers; rear pad brackets must be adapted.

The metal brackets on the original equipment and certain aftermarket brake pads require adjustment to clear the brake disc mounting while retaining the parking brake. It is essential to follow the instructions and use pre-prepared brake pads when available.

Subaru Impreza WRX STI (2008–2017)

Compatibility and Mounting Requirements:

Rear pad brackets must be modified.

Subaru WRX with Brembo calipers (2020)

Compatibility and mounting requirements:

Performance Pack and White Series.

Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.


Brake pads and braking systems for compatible vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s stock brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mounting components, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc D2-095 for compatible vehicles

What are the sizes of the D2-095 brake pads for my vehicle? The part number shown measures 316 × 20 mm and is mounted on the rear axle. The height of the brake pad, the mounting hardware, and the brake discs must also be compatible with the mounting.

Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake shoes are not included.

Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new brake discs or new one-piece brake rotors. Use a compound suitable for cast iron and your intended use. The metal brackets on the original brake pads and on some aftermarket pads require adjustment to clear the brake disc mounting while maintaining the parking brake. It is essential to follow the instructions and use pre-prepared pads when available.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of the Girodisc D2-095

  • 316 × 20 mm size for rear braking on compatible vehicles.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable alternative tracks to maintain a two-part mounting.
  • Left/right pair identified for mounting.
  • Compatible with existing aluminum brake rotors to preserve the benefits of the two-piece mounting on unsprung and rotating masses.

  • Diameter in mm
    316
  • Position
    Rear
  • Thickness
    20

16 other products in the same category: