Girodisc 380x34 Rear Brake Discs - Chevrolet Corvette Z06 (C8) (2022+) with CCB

GIRODISC
Reference: GIRO-A2-319
Supplier Ref.: A2-319

Price: CHF 1,873.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 1873 loyalty points (that is CHF 100.00 in vouchers)

Girodisc A2-319 rear brake discs, measuring 380 × 34 mm, enhance braking endurance during sustained use on the Chevrolet Corvette Z06 (C8) (2022+), Chevrolet Corvette Z06 (C8) with carbon-ceramic rotors (2022+), Chevrolet Corvette E-Ray (C8) with carbon-ceramic rotors (2022+). Their cast-iron pads and aluminum hubs form a floating assembly designed to manage thermal stresses and facilitate pad replacement during wear. Sold as a pair, including one left and one right rotor.

These rear discs are intended for the rear axle of compatible vehicles in the configuration listed below. They retain the compatible caliper mounting; any required spacers and brake pad specifications must be followed.

The curved internal cooling fins channel air through the rotor to dissipate heat during repeated braking. The floating mounting minimizes stresses caused by thermal expansion differences between the rotor and the housing and helps the rotor center itself between the brake pads, maintaining consistent contact under heat.

The hub is made of 6061-T6 aluminum. The high-strength steel drive pins are cadmium-plated to resist corrosion. Spring washers minimize cold-mounting noise while allowing the necessary compression for the floating mount.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting, cast iron, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.

On compatible vehicles originally equipped with carbon-ceramic rotors, this pair provides a conversion solution to high-quality cast-iron track rotors. It allows you to remove and store the expensive original carbon-ceramic rotors to preserve them during intensive use, while reusing compatible calipers. Use new brake pads suitable for cast iron and adhere to the pad shapes and any spacers specified by the part number. Replaceable brake pads reduce the cost of replacing braking surfaces in heavy-duty uses and offer a choice of linings to tailor bite and pedal reaction to the intended use.


Specifications for Girodisc A2-319 brake discs for compatible vehicles

  • Brand: Girodisc
  • PartNumber: A2-319
  • Position: rear
  • Sizes (diameter × thickness): 380 × 34 mm
  • Vehicles and models: Chevrolet Corvette Z06 (C8) (2022+); Chevrolet Corvette Z06 (C8) with carbon-ceramic rotors (2022+); Chevrolet Corvette E-Ray (C8) with carbon-ceramic rotors (2022+)
  • Braking surface: cast iron
  • Packaging: Pair of complete rotors, one left and one right, with disc bells.
  • Hub: 6061-T6 aluminum
  • Construction: two-piece floating mounting design
  • Alternative track number for these rotors: D2-319. Verify compatibility with the caliper generation before replacement.
  • Internal ventilation: directional curved fins
  • Number of internal fins: 72
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number A2-319

Chevrolet Corvette Z06 (C8) (2022+)

Compatibility and mounting requirements:

For vehicles equipped with factory cast-iron rotors.

On Z06 models equipped with the Z07 carbon-ceramic package, use the rear brake pad shape from the Z06 with cast-iron brakes.

Chevrolet Corvette Z06 (C8) with carbon-ceramic rotors (2022+)

Compatibility and Mounting Requirements:

For the Z07 carbon-ceramic package: use the rear brake pad shape from the cast-iron rotor version.

Chevrolet Corvette E-Ray (C8) with carbon-ceramic rotors (2022+)

Compatibility and Mounting Requirements:

For carbon-ceramic brakes: Use the rear brake pad shape from the Z06 equipped with cast-iron rotors.

Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these conditions before ordering.


Brake Pads and Brake Systems for Compatible Vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade flexible hoses and high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mountings, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc A2-319 for compatible vehicles

What are the sizes of the A2-319 discs for my vehicle? The model shown measures 380 × 34 mm and is mounted on the rear axle. The diameter alone is not enough: also check the brake type and mounting requirements.

Is the product sold in pairs? Yes. It includes a left and a right disc for the same axle. Both discs come with their disc bells.

Do I need to replace the brake pads on my vehicle?Yes. Always install new brake pads with new brake discs or new braking surfaces. Use a compound suitable for cast iron and your specific use. On Z06 models equipped with the Z07 carbon-ceramic package, use the rear brake pad shape from the Z06 with cast-iron brakes.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of the Girodisc A2-319

  • 380 × 34 mm size for rear braking on compatible vehicles.
  • 6061-T6 aluminum disc and floating mount to manage thermal stresses.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable tracks to maintain a two-piece mounting.
  • Left/right pair identified for mounting.
  • Aluminum housings to control the unsprung mass and rotating mass of the conversion kit.

  • Diameter in mm
    380
  • Position
    Rear
  • Thickness
    34

16 other products in the same category: