One-piece Girodisc 355x32 rear brake rotors - Ferrari 355 Challenge (1995–1999)

GIRODISC
Reference: GIRO-D2-054
Supplier Ref.: D2-054

Price: CHF 882.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 882 loyalty points (that is CHF 40.00 in vouchers)

The Girodisc D2-054 rear alternative brake pads (355 × 32 mm) allow you to replace the braking surfaces on Ferrari 355 Challenge (1995–1999) models while retaining the compatible brake rotors after inspection. These cast-iron pads maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without rotors.

The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting reduces stress caused by thermal expansion differences between the rotor and the caliper housing and helps the rotor center itself between the brake pads, ensuring consistent contact even when hot.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting, cast iron type, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc D2-054 rotors for compatible vehicles

  • Brand: Girodisc
  • PartNumber: D2-054
  • Position: rear
  • Sizes (diameter × thickness): 355 × 32 mm
  • Vehicles and models: Ferrari 355 Challenge (1995–1999)
  • Braking surface: cast iron
  • Packaging: pair of brake pads, one left and one right; rotors not included.
  • Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with original rotors.
  • Mounting hardware: new parts supplied with the kit; replace the entire rotor/hub mounting assembly during reassembly.
  • Part number for corresponding complete rotors: A2-054.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 30 mm
  • Original rotor diameter: 355 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number D2-054

Ferrari 355 Challenge (1995–1999)

Each application is subject to its specific brake system configuration, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.


Brake pads and braking systems for compatible vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement Brake Pads for Girodisc Rotors on the Ferrari 355 Challenge (1995–1999)

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the fasteners, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc D2-054 for Compatible Vehicles

What are the sizes of the D2-054 pads for my vehicle? The part number shown measures 355 × 32 mm and is mounted on the rear axle. The pad height, mounting hardware, and rotors must also be compatible with the mounting.

Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake shoes are not included.

Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Their shape and compound must be compatible with the D2-054 track and/or rotor and the calipers. Then break in the rotors and pads according to the prescribed procedures.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of Girodisc D2-054 Alternative Tracks

  • 355 × 32 mm size for rear braking on compatible vehicles.
  • Internal ventilation via curved fins to dissipate heat.
  • Replaceable alternative tracks to maintain a two-part mounting.
  • Left/right pair identified for mounting.
  • Compatible aluminum rotors are retained to preserve the benefits of the two-piece mounting on unsprung and rotating masses.

  • Diameter in mm
    355
  • Position
    Rear
  • Thickness
    32

16 other products in the same category: