One-piece brake rotors with a 325mm (12.8 in) diameter for Porsche Cayman (987.2 and 981) - Boxster (2012-2016)

GIRODISC
Reference: GIRO-D2-035
Supplier Ref.: D2-035

Price: CHF 942.00 Tax included
Available to order Within 10 days on average.
Unavailable in store (Promasens)
Earn 942 loyalty points (that is CHF 40.00 in vouchers)

Girodisc D2-035 rear alternative brake pads (325 × 20 mm) are designed to replace the braking surfaces on the Porsche Cayman (987.2) (2005–2013), Porsche Cayman (981) and Boxster (2012–2016), Porsche Cayman (981) and Boxster S and GTS (2012–2016), Porsche 718 (982) Cayman and Boxster (2016+), and Porsche 718 (982) Cayman and Boxster S and GTS (2016+), while retaining compatible brake rotors after inspection. These cast-iron tracks maintain the floating mounting’s functionality and facilitate maintenance of a braking system subjected to repeated stress. Sold in pairs, without rotors.

The curved internal cooling fins channel air through the disc to dissipate heat during repeated braking. The floating mounting limits stresses caused by differences in thermal expansion between the track and the caliper housing and helps the track center itself between the pads to maintain consistent contact when hot.

New brake pads must be installed with new rotors or brake discs. Their shape and compound must match the mounting configuration, cast material, and intended use; follow the specific requirements for this part number and perform the prescribed break-in procedure.


Specifications for Girodisc D2-035 tracks for compatible vehicles

  • Brand: Girodisc
  • PartNumber: D2-035
  • Position: rear
  • Sizes (diameter × thickness): 325 × 20 mm
  • Vehicles and models: Porsche Cayman (987.2) (2005–2013); Porsche Cayman (981) and Boxster (2012–2016); Porsche Cayman (981) and Boxster S and GTS (2012–2016); Porsche 718 (982) Cayman and Boxster (2016+); Porsche 718 (982) Cayman and Boxster S and GTS (2016+)
  • Braking surface: cast iron
  • Packaging: pair of brake pads, one left and one right; rotors not included.
  • Compatible rotors: rotors from the corresponding Girodisc kit; check by part number; not universally compatible with OEM rotors.
  • Mounting hardware: new parts supplied with the kit; replace the entire rotor/hub mounting assembly during reassembly.
  • Part number for corresponding complete rotors: A2-035.
  • Internal ventilation: directional curved fins
  • Minimum thickness: 18 mm
  • Original rotor diameter: 298 mm
  • Manufacturing of main components: United States

Vehicles compatible with Girodisc part number D2-035

Porsche Cayman (987.2) (2005–2013)

Compatibility and mounting requirements:

Base version; front/rear mounting in 340/325 mm with spacers and fasteners.

The existing mounting must retain the appropriate caliper spacers.

Porsche Cayman (981) and Boxster (2012–2016)

Compatibility and Mounting Requirements:

Base version; front/rear mounting in 340/325 mm with spacers and fasteners.

Porsche Cayman (981) and Boxster S and GTS (2012–2016)

Compatibility and mounting requirements:

Front/rear mounting in 350/325 mm sizes with spacers and fasteners.

Porsche 718 (982) Cayman and Boxster (2016+)

Compatibility and mounting requirements:

Base version; front/rear mounting in 350/325 mm with spacers and fasteners.

Porsche 718 (982) Cayman and Boxster S and GTS (2016+)

Compatibility and mounting requirements:

Front/rear mounting in 350/325 mm with spacers and fasteners.

Each application is subject to its specific brake system, calipers, and any requirements for brake pads or spacers. Please verify these requirements before ordering.


Brake Pads and Brake Systems for Compatible Vehicles

For sports driving or track use, we recommend Endless, Pagid Racing, or Ferodo DS Uno brake pads, whose compounds are designed for high braking demands. Unless otherwise specified for the Girodisc mounting, the brake pad shape remains identical to the original, allowing the vehicle’s brake calipers to be retained. The choice of compound must be suited to the intended use.

For intensive use, we recommend compatible aviation-grade hoses and a high-performance brake fluid that meets the vehicle’s specifications, along with proper bleeding and fluid replacement. This recommendation complements the mounting, which is compatible with the original hydraulic system.


Replacement brake pads for Girodisc rotors on compatible vehicles

When the braking surfaces on your Girodisc rotors are worn out, replace them with alternative tracks compatible with your existing rotors. The aluminum rotors can be reused for up to three pad replacements, subject to their condition, inspection of the mounting components, and compliance with mounting instructions. Always use a new mounting kit each time you replace the pads.


FAQ — Girodisc D2-035 for compatible vehicles

What are the sizes of the D2-035 brake pads for my vehicle? The part number shown measures 325 × 20 mm and is mounted on the rear axle. The height of the brake pad, the mounting hardware, and the brake discs must also be compatible with the mounting.

Is the product sold in pairs? Yes. It includes a left and a right component for the same axle. The brake shoes are not included.

Do I need to replace my vehicle’s brake pads?Yes. Always install new brake pads with new rotors or new braking surfaces. Use a compound suitable for cast iron and your intended use. The existing mounting must retain the appropriate caliper spacers.

How do I identify the left and right sides? Girodisc rotors come with a label attached to each rotor: LEFT for the left side and RIGHT for the right side, as viewed from the direction of travel. On a left-hand-drive vehicle, “LEFT” corresponds to the driver’s side and “RIGHT” to the passenger side. Follow these labels and the instructions. On models with curved internal fins, the rolling direction depends on this internal ventilation; the surface grooves alone are not sufficient to determine the side.

How do I break in this mounting on my vehicle? Follow the Girodisc procedure and the brake pad manufacturer’s instructions to build up an even transfer ply. The PDF documents below detail installation and break-in.


PDF Documents for Mounting and Break-in

We have included two PDF documents below: an instruction manual for installing and breaking in the discs, and an instruction manual for installing new tracks on existing bowls. Consult the document that applies to your specific task before you begin.


Key Features of the Girodisc D2-035

  • 325 × 20 mm size for rear braking on compatible vehicles.
  • Internal ventilation via curved fins to dissipate heat.
  • Alternative tracks to maintain a two-part mounting.
  • Left/right pair identified for mounting.
  • Compatible with existing aluminum brake rotors to preserve the benefits of the two-piece mounting on unsprung and rotating masses.

  • Diameter in mm
    325
  • Position
    Rear
  • Thickness
    20

16 other products in the same category: